Main parameters of jaw crusher

Whether designer or user, in order to properly design and use of jaw crusher and to ensure the reliability and economy of operation, must understand and master the main parameters of jaw crusher. Because the theoretical calculation error of some parameters is large and not practical, only the more practical empirical calculation formula is introduced here.

1. Dimensions of the feed port and the width of the discharge port The size of the feed port is a very important parameter when selecting the size of the jaw crusher, and it is also the data that the operator should know. At present, in China, the length L of the feed port is 1.25-1.6 times the width B, that is, L=(1.25-1.6)B. For large jaw crushers, L = (1.25 - 1.5) B; for small jaw crushers, L = (1.5 - 1.6) B. Feed port width B determines the maximum feed size _Dmax of the crusher. Generally, D _max = (0.75 - 0.85) B is taken. In China, the simple pendulum type usually takes D _max =0.75B; the complex pendulum type usually takes D _max =0.85B.

The width e of the discharge opening depends on the maximum discharge size d _max and the swinging stroke S of the moving jaw. It can also be determined by referring to the feed port width B. Usually, the simple pendulum type takes e=d _max -S=(1/5-1/7)B; the complex pendulum type takes e=d _max -S=(1/7-1/10)B.

2. The angle of the jaw crusher is the angle between the moving jaw and the fixed jaw. During the crushing process, sufficient friction is required between the ore and the moving face to prevent the ore from sliding upward or jumping out of the feed port. The jaw angle of the jaw crusher is generally selected between 17 ° and 24 °. Correct selection of the angle of the joint has great significance for improving the productivity and crushing efficiency of the crusher. Increasing the angle of the teeth increases the breaking ratio, but at the same time the productivity will decrease. Reducing the angle of the jaws increases the productivity of the crusher, but the crushing ratio will decrease, so the designer should consider the overall consideration when selecting the angle. In foreign countries, a curve-shaped crushing cavity with a deep and small angle is generally adopted, in order to obtain higher productivity, and also ensure that the crushing ratio is not reduced. At present, China is working hard in this direction.

3. Rotating speed of eccentric shaft At present, in actual production, the following empirical formula is commonly used to determine the rotational speed n of the eccentric shaft, and the calculation result is close to the actual rotational speed. When the feed port width B < 1200 mm, n = 310 - 145 B (r / min); when the feed port width B ≤ 1200 mm, n = 160 - 42 B (r / min).

4. Productivity The productivity of a jaw crusher refers to the amount of ore processed in a unit of time. It is a quantitative indicator of the crusher's processing capacity. In the design, the following empirical formula is usually used to calculate its productivity Q:

Q=K ₁ K ₂ q ₀ eδ/1.6(t/h)

Where K ₁ - ore severability coefficient (Table 1); K ₂ - particle size correction factor (Table 2); q ₀ - productivity per unit discharge opening width (t/mm·h) (Table 3) .

Table 1 Ore Fragility Coefficient K ₁

Ore hardness	Compressive strength / Pa	Platt hardness coefficient	K 1
hard Medium hard soft	1.6~2 0.8~1.6 <0.8	16~20 8~16 <8	0.9~0.95 1.0 1.1~1.2

Table 2 Particle size correction factor K _{2 of} coarse crushing equipment

Feed particle size D max / feed port width B	0.85	0.6	0.4
K 2	1.0	1.1	1.2

Table 3 Productivity of the unit discharge opening width of the jaw crusher q ₀

Crusher specifications / mm × mm	250×400	400×600	600×900	900×1200	1200×1500	1500×2100
q 0	0.4	0.65	0.95~1.00	1.25~1.30	1.9	2.7

Special Effect Pigments

As a leading supplier of effect pigments in China, we take pride in offering high-quality and competitive pigments to our global customers. With over 20 years of experience in the industry, we have built a strong reputation for excellent service.

Our Special Effect Pigments category includes a wide range of products that can add a touch of magic to your creations.

• Fluorescent Pigments : These pigments exhibit vibrant and intense colors under UV light, making them perfect for eye-catching designs.
• Glow In The Dark Pigments: These pigments absorb and store light energy, allowing them to glow in the dark. They create a striking and luminescent effect in various applications.
• Thermochromic Pigments: These pigments change color with temperature variations. They offer an exciting way to create dynamic and interactive designs that react to heat.
• Photochromic Pigments: These pigments change color when exposed to sunlight or UV light. They provide a captivating transformation in outdoor environments.
• Holographic Pigments : These pigments create a mesmerizing rainbow effect by diffracting light. They add depth and dimension to any product or surface they are applied to.
• Chromashift Chromaflaks: These pigments exhibit a unique color-shifting property, appearing different shades when viewed from various angles. They offer a truly captivating visual experience.
• 3D Cat Eye Pigments: These pigments create a stunning cat-eye effect with a three-dimensional depth. They are widely used in nail art and other creative applications.
• Copper Gold Powders: These pigments give a luxurious metallic copper gold finish to your products, adding elegance and sophistication.
• Aluminum Powders: These pigments provide a metallic sheen and come in various particle sizes, allowing for different effects and applications.

Special Effect Pigments,Color Changing Pigments,Effect Pigment Powder

Kolortek Co., Ltd. , https://www.micapowders.com