A: High pressure solenoid valve product leakage reasons 1, high pressure solenoid valve the actual working environment and the properties of the media, beyond the scope of product adaptation. 2, high-pressure solenoid valve installation error, or filling method does not lead to high pressure solenoid valve product leakage. 3, after a long period of use, high pressure solenoid valve mechanical parts wear, such as seals and packing leakage caused by wear.
Two: high-pressure solenoid valve product leakage inspection points 1, high-pressure solenoid valve product disassembly and maintenance requirements of the working environment must be clean 2, clean the high-pressure solenoid valve outside to remember the nameplate and various signs 3, pay attention to check the base Contact with the valve plate
4, check the high pressure solenoid valve mechanical seal parts wear degree.
High-pressure solenoid valve fault check after the operation: In the high-pressure solenoid valve troubleshooting, if found damaged high-pressure solenoid valve components, should be replaced or repaired. Pay special attention to several important packing and seals. After the installation is completed, it can not be put into use immediately, it is required to carry out the work test and test the working intensity and tightness of the high-pressure solenoid valve.
High-pressure solenoid valve products are fluid transport equipment used in a very wide range of products, usually with pipelines, pumps and other fluid transport equipment supporting the use of. The correct operation and use of the solenoid valve life extension and reduce the failure rate has a tremendous role in the maintenance and repair of solenoid valve products and the specific operation of the work are as follows:
1, high-pressure solenoid valve products installed, users need to access the medium for testing, solenoid valve products work properly before they can be formally put into work.
2, high-pressure solenoid valve products in the process of using, should pay attention to the pressure of the product range, more than the working pressure of the product range will damage the solenoid valve products, resulting in leakage and loss to the user. If there is abnormal pressure or exceeds the actual working range of the solenoid valve, immediately close the front and back manual solenoid valve to stop the solenoid valve.
3, mechanical equipment at work in the state, should avoid loosening occurs, to reduce mechanical vibration, reduce mechanical damage, extend the life of the solenoid valve.
4, high-pressure solenoid valve in the working state, should avoid collisions and contact with other heavy objects. So as not to affect the solenoid valve work.
5, high pressure solenoid valve product seal is one of the important parts of the solenoid valve, solenoid valve should ensure that the sealing performance. Keep the solenoid valve seal inside clean.
6, for work in a special environment of the solenoid valve products, such as access to water, excessive working environment debris, etc., should be equipped with suitable solenoid valve protective equipment.
7. If you are not using the high-pressure solenoid valve for a certain period of time, users should close the manual valve before the valve and clean the inside of the solenoid valve to ensure the dryness of the solenoid valve and then save it.
8, due to the variety of solenoid valve models, each model has its own characteristics and scope of work. For new users, you can refer to the Code Code valve industry sales and technical staff product introduction, choose more suitable for your product.
European type impact crusher is mainly used in metallurgy, mining, cement, chemical industry, refractory materials, ceramics and other industrial sectors. It is widely used in highway construction, water conservancy engineering, construction crushed stone, machine-made sand processing and other fields, and is very suitable for crushing various soft and hard ores. Perform coarse, medium, and fine crushing operations.
This machine is a crushing machine developed using impact energy to crush materials. When the material enters the action zone of the plate hammer, it is crushed by the high-speed impact of the plate hammer and thrown towards the impact device installed above the rotor to break again. Then, it bounces back from the impact lining plate to the action zone of the plate hammer and breaks again. This process is repeated until the material is crushed to the required particle size and discharged from the lower part of the machine. Adjusting the gap between the counterattack frame and the rotor frame can achieve the goal of changing the particle size and shape of the material. This machine adopts a spring safety device behind the impact plate. When non broken objects enter the crushing chamber, the front and rear impact frames retreat, and the non-broken objects are discharged from the machine.
European Impact Crusher,Impact Crusher,Impact Rock Crusher
SiChuan TieYing Machinery Manufacturing CO.,LTD; , https://www.tieyingcrushers.com